Dana 30 spindle removal tool

Remove the outside spindle nut, locking washer, inner spindle nut, and inner washer. A 2 1/16" spindle nut socket is the best tool for removing the spindle nut. Pull off the brake hub and drum/rotor. Remove the Spindle: On the drum brake, you must remove all the springs, shoes, and brake hose at this time. Brake tools pay for themselves when ... Dana 30 Front Assembly Parts for Dana 30 open knuckle front assemblies sort by: regular price (lowest) regular price (highest) date (newest) date (oldest) name (a thru z) name (z thru a) customer rating (highest) customer rating (lowest)
Dana 30 Rebuild: Outer Axle Seal removal Replacing axle seals on Dana 30 on my '69 Sport. I expected the "outer seal" to be between the axle stub and the spindle so a bit surprised to find these (image 38 is driver side, image 68 passenger) installed in the carrier tube ends. Place a new axle shaft seal on tool 5041-1 and position the assembly in the disconnect housing. Screw threaded bar 5041-2 through the seal and into tool 5041-1. Place tool 5041-3 and the nut on the end of the bar and tighten the nut until the tool reaches the shoulder of the bar. Having the right tools makes the job far easier, whie the wrong tools can make the job miserable, if not impossible. Bearing Pullers. Works with an impact gun to quickly and safely remove carrier bearings without damaging them; Comes with a handy bench top stand and works with up to most standard one ton applications; Housing Spreaders

Boxer puppies ottawa

DESCRIPTION: The Main Rotor Spindle Removal tool is used to remove and install the main rotor spindle assembly safely and effectively, eliminating potential damage to main rotor hub components. It s a rectangular piece on machined aluminum with a custom-fit cut-out to fit over the spindle assembly. The wheel bearing and hub assembly replacement is one of the most common repairs performed on the popular Dana 30 front axle. The three-bolt wheel bearing & hub assembly was used on the 1984 and up Jeep Wranglers (YJ)& (TJ) and all Jeep Models from 1991 to the current models with the exception of the Liberty and the Rubicon.
Home » Jeep Tools » Jeep Driveline Tools. ... OMIX Spindle Nut Socket for 41-86 Jeep Vehicles with Dana 25, Dana 27 or Dana 30 Axles. ... Ox U-Joint Trunion Removal ...

Install the camber shim making sure the wider side is on the top for adjusting negative camber or at the bottom to adjust positive camber. After you reinstall the spindle and caliper bracket (the caliper bracket shown in the article is only found on 76-79 CJ’s) this is a good opportunity to check the camber using a level across the spindle surface.
The wheel bearing and hub assembly replacement is one of the most common repairs performed on the popular Dana 30 front axle. The three-bolt wheel bearing & hub assembly was used on the 1984 and up Jeep Wranglers (YJ)& (TJ) and all Jeep Models from 1991 to the current models with the exception of the Liberty and the Rubicon. Bought this for the spindle nuts on my GM Dana 60 King Pin. I haveYukon Spindle nuts and I had to spend about 30 mins filing down the 4 key ways on the socket. They were to wide to fit in the slots of the nuts. Looks to be deep enough to fit over the axle shaft and reach the inner spindle nut.

Ck2 stuck on loading events

Home » Jeep Tools » Jeep Driveline Tools. ... OMIX Spindle Nut Socket for 41-86 Jeep Vehicles with Dana 25, Dana 27 or Dana 30 Axles. ... Ox U-Joint Trunion Removal ... Remove the outside spindle nut, locking washer, inner spindle nut, and inner washer. A 2 1/16" spindle nut socket is the best tool for removing the spindle nut. Pull off the brake hub and drum/rotor. Remove the Spindle: On the drum brake, you must remove all the springs, shoes, and brake hose at this time. Brake tools pay for themselves when ...
Jeep Cherokee (1984-2001) Pull Tip: Sometimes the axle nut can be stubborn. If it is, find a pipe or muffler from the yard and use it to extend the leverage on your breaker bar!